How to calibration aromatic suspension Mercedes Benz replace front shockupser DTC trouble code C153313 right front dumping valve malfunction DTC trouble code C153214 C156E00 calibration of the vehicle level was not performed Mercedes Benz
HELLO GUYS FIRST OF SORRY BECAUSE LOT
OF PEOPLE THE NOT UNDERSTAND MY
LANGUAGE & NO SUBTITLE, IN VIDEO AND
VIDEO QUALITY ALSO NOT GOOD
BECAUSE EVERY TIME AFTER UPDATE SCANNER OPTION CHANGE SO LITTLE BIT CONFUSION AFTER WATCHING THIS VIDEO
1 IF YOU FACING SAME PROBLEM ON YOUR CAR 🚗 SO FIRST OF CHECK COMPRESSOR PUMP MOTOR IS WORKING OR NOT IF NOT WORKING SO YOU CAN CHECK FUSE AND RELAY IF YOU FIND FUSE AND RELAY OKAY SO YOU CAN CONNECT SCANNER AND AFTER CONNECT SCANNER SELECT AIR SUSPENSION AND CLICK SPECIAL FUNCTION THEN CLICK ACTIVATION TEST NOW YOU CAN DO EASILY ON OF COMPRESSOR MOTOR PUMP ON SCANNING TOOL SPECIAL FUNCTION
2 IF YOU WANT TO CALIBRATION YOUR MERCEDES BENZ CAR AND IF YOU HAVE A MERCEDES BENZ ORIGINAL SCANNER LIKE MB STAR SO YOU CAN DO EASILY BUT IF YOU HAVE A LOCAL MARKET IS SCANNER AUTEL SO YOU CAN DO EASILY AUTOMATIC
3 WHEN YOU START CALIBRATION SO FIRST OF CERTIFIED NO ANY DTC ON AIRMATIC SUSPENSION ONLY CALIBRATION BEFORE CALIBRATION YOU CAN CLEAR DTC
4 WHEN YOU DO CALIBRATION SO FIRST STEP YOU CAN CHECK EARTH LEVEL WHERE PARK YOUR CAR NEED TO PLAN LEVEL 🎚️ TRY TO AUTOMATICALLY OPTION BUT IF YOU DOING MANUAL SO REQUIRED VALUE
IT IS DEPEND ON MODEL
W221 Airmatic calibration Value
FRONT (3.1) both sides
REAR ( -1.5) both sides
W211 Airmatic calibration Value
FRONT ( 3.5 ) both sides
REAR ( - 1.1 ) both sides
form level calibration with the values entered?
F front inclination angle 3.1
R rear inclination angle -12
Launch X431 scanner or any
front vehicle level
Rear vehicle level
Left front vehicle level 🎚️ 131 mm
Right front vehicle level 🎚️ 130 mm
Rear vehicle level 🎚️ 130 mm
Signal 1 of component 822/8,Left front level
sensor ( 2.40)
Signal 1 of component 822/9,Right front level sensor (2.69)
1.Connect scanner device to Benz OBD port,then choose Benz V48.11 or a later version.
2 Choose 221-S class (as your car and click OK,
3.Select System Selection
4 Choose Suspension (chassis CAN bus
5 Choose special function. Note: Before level calibration, read and clear DTCs first. If any fault exists,rectify the fault first. Ensure that the air suspension system is normal.
6 Choose level calibration to check the hint message, and click OK.
7 Check height and sensor information
8 Check the sensor, front axle specified value, rear axle specified value, and roles of F2-F 10 keys. Press F3-F 10 to adjust the level height to standard value. Then, press F2 to input the angle. V
9 Set the FL tilt angle to 1.9 (in Figure 7, front axle specified value: tilt angle 1.4, 2.4, use the middle value 1.9 Click OK,
10.Set the FR tilt angle to 1.9. Click
11.Set the RL tilt angle to -2.0 (rear axle specified value: tilt angle (-1.6°)-(-2.3°), use the middle value-2.0°) Click OK.
12.Set the RR tilt angle to -2.0 and click OK
13,Check tilt angle data and click Yes to
14 perform height calibration.
Height calibration succeeds. Click OK
calibration
control module is already calibrated
