I started with a V0.0 Kit from Aliexpress (now it's 0.1, which is better in any respect)*:
Formbot Voron V0.1 Kit (AliExpress) [ Ссылка ]
LDO Voron V0.1 KIT (Caribou3D) [ Ссылка ]

Recommended Kits for bigger DIY printers:
Voron 2.4 Kit (AliExpress) kit bit.ly/3PklmWE
Voron Trident Kit (AliExpress) [ Ссылка ]

STL files, instructions and BOM on the recent upgrades:
[ Ссылка ]

Support my work at Patreon:
[ Ссылка ]

My Instagram and Twitter - more about my doings and behind the scenes:
Instagram: [ Ссылка ]
Twitter: [ Ссылка ]

Watch the print at 1100mm/s:
[ Ссылка ]

💚Pizza, Beer and Coffee helps me going on💚
[ Ссылка ]
💚Thanks to all who support/ed my work💚


---------------Settings:

Filament: ESUN ABS+ - a great choice filament for strong parts and easy printing
[ Ссылка ]

T_Hotend = 290C
T_Bed = 90C

Requested Speed: 1000mm/s
Acceleration: 35.000 mm/s²
square_corner_velocity: 15mm/s
Nozzle: 0.4mm
Layer Height: 0.1mm
Line width: 0.4mm
Volumetric flow: 40mm³/s
Lengths of straights: 65mm
Lengths of printing @ REAL 1000mm/s: 35mm

Xxxx ALL DESIGNS AVAILABLE SOON xxxX
@ Voron Users / Thingiverse



*******UPGRADES* STAGE 1 on my Voron V0 - VIDEO DEEP DIVES and ANALYSES incoming:

For years now, I use BigTreeTech/BIQU products - very much recommended:
(I was sponsored with an Octopus Board V1.1, TMC2209, 70W Heater and PT1000 thermistor)
Get the Octopus Board here:
[ Ссылка ]

—MOTION (Part 1: Video Deep Dive incoming)

Nema14 spec Voron V0.1 @1.7A (OMC 14HS20-1504S)
[ Ссылка ]

F623 bearings instead of toothed idlers
[ Ссылка ]

WD40 specialist dry lubricant for rails (PTFE)
[ Ссылка ]

Gates-LL-2GT 6mm belts
[ Ссылка ]


— EXTRUSION: (Part 2: Video Deep Dive)
Slice Engineering Mosquito Magnum (5% off!): [ Ссылка ]

VolcoMosq Block (+9mm melt): [ Ссылка ]

E3D Hemera (Bowden config)
[ Ссылка ]

Capricorn Bowden Tube
[ Ссылка ]

50W heater (24V)
[ Ссылка ]

PT1000 temp sensor
[ Ссылка ]

Boron Nitride Paste @ heater, thermistor and heat break
[ Ссылка ]


— COOLING (Part 3: Video Deep Dive)
4010 blower fans (24V), updated toolhead
[ Ссылка ]

optimized air ducts for part cooling with aluminium tape insulation
[ Ссылка ]

External Static Cooling: 4x4020 fans (24V)
[ Ссылка ]

4x40mm heatsink at AB stepper motors
[ Ссылка ]

2x 4020 / or 4010 fans (5V) at heat sinks (stepper motors)
[ Ссылка ]

25mm axial fan (5V) for stepper drivers
[ Ссылка ]


— Software / Firmware / Controllers (Part 4: Video Deep Dive):

Klipper
[ Ссылка ]

Raspberry Pi Zero W (Mainsail)
[ Ссылка ]

Raspberry Pi 3B (Input Shaping and Octoprint)
[ Ссылка ]

Alternative: Raspberry Pi4:
[ Ссылка ]

Simplify 3D: multi processes used
[ Ссылка ]


-------------------------------------------------------
My modest video gear*:

iPhone 11 Pro: [ Ссылка ]
Smartphone video rig: [ Ссылка ]
GoPro Hero 9: [ Ссылка ]
FLIR ONE PRO: [ Ссылка ]
Similar to the soft boxes I use: [ Ссылка ]
Similar to the tripod I use: [ Ссылка ]

*Amazon links are affiliate links at no extra costs for you!

#JoinTheSpeed
#247printing
#volcomosq
#SpeedBoatRace

свернуть