The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. In this comprehensive tutorial video guide, Aiman will take you through the steps of troubleshooting and diagnosing the red flashing light on your Litter-Robot III (LR3) Open Air automatic self-cleaning robotized litter-box if it stopped working and displaying the above fault message or error code. Here are the #ᴬᴰlinks to some of the components, parts and tools required for this repair or alternative products you might want to consider:
1. [ Ссылка ] | Litter-Robot 3 Connect & Ramp by Whisker - Automatic, Self-Cleaning Cat Litter Box, WiFi Enabled, Works with Any Clumping Litter, Designed & Assembled in USA (Grey), 1-Year WhiskerCare Warranty
2. [ Ссылка ] | PetSafe ScoopFree Complete Plus Self-Cleaning Cat Litterbox - Never Scoop Litter Again - Hands-No Cleanup With Disposable Crystal Tray - Less Tracking, Better Odor Control - Includes Disposable Tray
3. [ Ссылка ] | MyfatBOSS 10-Pack Carbon Filters Compatible with Litter-Robot 3, Activated Carbon Litter Box Filter Compatible with Litter-Robot 3 Self Cleaning Cat Litter Box Filters, Accessories Replacement
4. [ Ссылка ] | Omilik 15V AC Adapter Charger Replacement for Litter-Robot II 2 Bubble,Classic,III 3 Open Air Power Supply Litter-Robot III Open Air Self Cleaning Litter Box Power Cord
Or Click on Amazon link here and search for what you need: [ Ссылка ]
In most cases, the red blinking or flashing light on the front panel indicates defective CATS sensor, but the first thing you should do before taking further steps is to do the following:
Please check your unit for:
* The litter is above the fill line or in excess of 10lbs.
* CATS has not been reset after adding weight
* The waste drawer has too much weight
* The unit is sitting on an uneven surface ‐ grout lines on tile floor or in a bathtub.
* The unit is pushed into a corner, against a wall, or furniture
* Objects are resting or pressing on the unit
To test your changes, power the unit off and then on. Allow the unit to complete the start‐up cycle and return Home with a solid blue light which indicates your unit is operating normally.
Always press Reset after emptying the waste drawer, adding litter, or moving the unit. You can also turn the unit OFF then ON to ensure the baseline is set properly. When pressing Reset, watch for the blue light to quickly flash one time. This indicates CATS has been successfully reset.
If none of the above solves the issue:
1. Remove the bonnet.
2. Remove the globe
3. Replace the bonnet
4. Press Cycle (without the globe on the unit)
5. Allow the motor to run for 5 seconds, at any point, does it stop and flash red? If no, then excess weight needs to be removed from the globe. If yes, (it blinks red), then watch this video for further steps.
In this video, Aiman will show you how to take apart Litter-Robot III and test the CATS sensor to see if it is actually the culprit by using a simple multi-meter to measure the resistance in the pressure sensor. Aiman will also show you how to jump the CATS sensor should you need to continue to operate LR3 while waiting for the parts to arrive. Please note that you should only do this at your own discretion as jumping or bypassing the sensor might damage the LR3 circuit board. He will then show you how to remove, replace and repair the CATS sensor.
When putting back the bottom foot bolt, It's essential that you DO NOT overtighten the nut as it will crush the cat sensor.
If your foot is white (and the bolt is 1 7/8'' cm) : you need to screw for the bolt to be about ~1/4" (6.35mm) from the bolt.
If your foot is black (and the bolt is 1 5/8'' cm) : you need to screw for the bolt to just be a mm from the bolt.
Taking apart the unit is actually quite simple and easy, however there are a few specialized tools you might need and Aiman will explain that in this video.
If you need to order the parts, click on the following link: [ Ссылка ]
For those who don't already own LR3 and if you are interested in this unit you'll have to buy it directly from Litter-Robot website, but Amazon has a machine with similar features called CatGenie A.I. Artificial Intelligence Self-Washing Cat Box (Latest Model), which you might want to check it out: [ Ссылка ]
Thanks for watching...This video is presented to you by Aiman-Imran Anuar. You can watch more of #Aiman_DIY_Fixit #Our_Pets_In_Action #Cool_Gadgets_For_Pets videos on #EyeOnAiman Youtube Channel & Facebook Page.
Note: This video is NOT sponsored. Some product links are affiliate links which means if you buy something we'll receive a small commission. As an Amazon Associate we earn from qualifying purchases.
Recording Date: September 9, 2018
Video URL: [ Ссылка ]
