Antikythera Fragment #5 - #Ancient Tool Technology - The First #Precision Drill Bit, by Clickspring.
There are a number of cutting tools implied in the wreckage of the Antikythera Mechanism, and one of the most interesting is the drill bit. In this video I explore a possible method of how an effective and precise drill bit could have been made in antiquity.
The video where I show the carburisation process in detail can be found here: [ Ссылка ]
If you would like to help support the creation of these videos, then head on over to the Clickspring Patreon page: [ Ссылка ]
________________________________________________________
A very special thank you to Patrons:
Sinking Valley Woodworks ([ Ссылка ])
Glenn Trewitt
Christopher Warnock
Mike Manfrin
Steven Sladewski
Rollin W. Patrick, Jr.
Jim Popwell
Gary Levario
Pete Askew
Norman Lemke
Andre van Soest
Andrew Smith
Bernd Fischer
Rudolph Bescherer Jr
Sam Towne
Adam Slagle
Jack Cause
Jeremiah G. Mort
Dave Seff
Olof Haggren
Stassinopoulos Thomas
Florian Ragwitz
Larry Pardi
Michael Harmon
Lonnie Koehn
Tim Bray
________________________________________________________
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - [ Ссылка ]
Panasonic X920 - [ Ссылка ]
Tools & Shop Products:
"Solidworks 2013 Bible": [ Ссылка ]
"Hardening, Tempering and Heat Treatment (Workshop Practice Series)" - [ Ссылка ]
Salamander A-6 SUPER Clay Graphite Morgan Melting Crucible: [ Ссылка ]
Norton 1-by-2-by-8-Inch Fine/Coarse India Combination Oilstone, Red: [ Ссылка ]
Saint Gobain (Norton) - 4 Arkansas Stones + case: [ Ссылка ]
Abbreviated Transcript:
00:12 The existence of an Ancient style of drill bit is strongly implied in the wreckage of the Antikythera Mechanism. And its fabrication would have likely hinged on a crucial process: The ability to take a malleable wrought iron, and transform it into something hard enough to cut bronze.
00:28 I've covered the process in detail in a separate video, but essentially it involves packing an animal based charcoal and salt around the soft iron, sealing it in clay, and then heating it up to a red heat I'm using a low carbon mild steel as a substitute for Ancient wrought iron. Its soft and ductile.
01:00 But there are some great examples of long slender turning to be found within the wreckage of the mechanism itself. There's a shaft that extended from the lunar phase gearing up to the phase display on the front dial that's roughly 4mm in diameter.
01:16 And there are numerous other pins and shafts, some less than a mm in diameter. I'm using a modern furnace for convenience, but a traditional charcoal furnace is quite capable of generating the required temperature. Once at a red heat, the process of carburising the iron is purely a time exercise.
01:51 So I reheated the rods, rolled them straight on a flat surface, and then requenched. The once soft metal is now very hard, but also extremely brittle, and so easily fractures under a light bending load. So to be of use as a cutting tool, it needs to be tempered, in this case to a light straw color.
02:40 I can see this end of the rod is a good straight section, so that'll become the actual bit, and the excess will be removed at the end of the process. A gentle heat raises the temperature of the rod until a pale straw color just reaches what will become the cutting end. The material is now in a tempered state. Still very hard, but tough rather than brittle.
03:23 Despite no longer being widely used, it still has a number of attributes to recommend it. The first being that its very easy to make. Because the primary surfaces can all be formed by hand, on flat abrasive stones. The cutting edges can be shaped for unidirectional cutting, or as in the case that I'm showing onscreen, for single direction cutting.
03:59 And once the operational length has been decided, it can be permanently set by scoring the metal with a file, and then snapping off the excess material.
04:38 In its rigid cross section form, this sort of drill bit will often perform much like a traditional D bit. Delivering a very straight deep hole. Now there is of course an obvious drawback to the drill bit design: The need to repeatedly withdraw it from the work to clear the chips.
05:36 As soon as the cutting edges start to dull, a quick hit on the stones will bring them back to original condition. Now you won't want to throw out your twist drills any time soon, but its a great option to keep in mind for those rare occasions when you really do need a custom drill bit.
References:
Watchmaking by Daniels: [ Ссылка ]
The many books and DVD's by WR (Bill) Smith: [ Ссылка ]
Antikythera Fragment #5 - The First Precision Drill Bit, by Clickspring.
