See how I removed the High Pressure Power Steering Hose in a hard to reach area on a Chrysler Crossfire without taking off the engine motor mount. Click on SHOW MORE for all tools used and for each specific setup utilized. Please 👍👍👍 & 🔔 Subscribe if this video helps.
👉👉👉
Normally removing a power steering hose is easy, but in some cars it could be hard just to access. This video shows you how to access it, and hopefully help you to replace the hose with ease even if the hose and its nut are in difficult areas to get to and remove.
If you need to see first where and how to pinpoint your power steering leak, then you can check out this quick video here: 👉👉👉 [ Ссылка ]
Their are about 30 tools and parts you will need to gather:
Floor Jack [ Ссылка ]
Jack Stands [ Ссылка ]
Oil drain pan [ Ссылка ]
Syringe Pump [ Ссылка ]
Oil funnel [ Ссылка ]
Recyclable container or empty jug
ATF [ Ссылка ]
Mineral Spirits Turpentine [ Ссылка ]
Shop Towels [ Ссылка ]
Gloves [ Ссылка ]
Kneepads [ Ссылка ]
Flashlight
Breaker Bar 3/8" [ Ссылка ]
Ratchet Wrench 3/8" [ Ссылка ]
18 MM wrench [ Ссылка ]
Crowfoot Wrench set standard [ Ссылка ]
Adapter set [ Ссылка ]
Universal Joint swivel Adapter set [ Ссылка ]
1/4" Extension set [ Ссылка ]
3/8" Extension set [ Ссылка ]
Flat Tip Screwdriver [ Ссылка ]
Torque Wrench 3/8" [ Ссылка ]
Power steering oil to choose from (Make sure the oil is compatible with your vehicle before purchasing):
Pentosin 1405116 CHF 11S Hydraulic fluid [ Ссылка ]
Lucas Oil Power Steering [ Ссылка ]
Prestone PS Fluid [ Ссылка ]
These tools help determine where your leak is:
UV Flashlight [ Ссылка ]
UV Dye [ Ссылка ]
Actual part that needs to be replaced:
Power Steering High Pressure Hose
This is the one I used on this Mercedes or Crossfire Car:
➡️➡️➡️ [ Ссылка ]
These are the 3 setups you need to make depending on where you are in removing the power steering hose:
Setup 1: will help in loosening the nut
You need this in this order from top to bottom a:
18 mm or 11/16" Crow Foot wrench
1/4" to 3/8" adapter
1/4" swivel joint
1/4" Extension that is 6" long
1/4" to 3/8" adapter
3/8" extension that is 10" long
Setup 2: allows you to easily turn and remove the PS nut fully from the engine area
18mm or 11/16" Crow Foot wrench
3/8" extension that is 3" long
Setup 3: is used to fully tighten the nut when reinstalling the new power steering high pressure hose
18 mm or 11/16" Crow Foot wrench
3/8" to 1/2" adapter
1/2" breaker bar that is at least 12" long
If you would like to help support and grow this channel you can get me a cup of coffee ☕ here: ➡️ [ Ссылка ]
OR
➡️ [ Ссылка ]
AND/OR make videos you think can help others.
Remember to always think how to be crafty as their may be other ways to accomplish a task like this power steering nut trick without taking off anything else off underneath the car.
Thanks for watching and learning. Let me know your thoughts in the COMMENTS below.
👍 & 🔔 #fixcaryourself
