Find the parts used in the video on CarParts.com just there [ Ссылка ]

⚙️ NEEDED CARPARTS AND PRODUCTS
- Catalytic converter : [ Ссылка ] and [ Ссылка ]

- Penetrating oil

- Exhaust sealant

- Grease

💪 TIGHTENING TORQUES
- Oxygen sensors : 34 Ft-lbs

- Catalytic converter to Exhaust manifold nuts : 30 Ft-lbs

- Front driveshaft-to-transfer case flange bolts (4WD models) : 41 Ft-lbs

- Rear driveshaft-to-differential flange bolts (2WD or 4WD models) : 76 Ft-lbs

- Transmission crossmember-to-chassis bolts : 66 Ft-Lbs

- Transmission mount-to-crossmember nuts : 72 Ft-Lbs


🛠 TOOLS
The toolbox recommended by CARPARTS.COM to repair your Ford F-150 :
- [ Ссылка ]

List of the tools we used to replace the catalytic converter on a Ford F-150 :
- Hydraulic jack : [ Ссылка ]
- Jack stands : [ Ссылка ]
- Wheel lug wrench
- Wire brush
- Marker
- Ratchet x2
- 13mm socket
- 18mm socket
- 15mm socket
- 10mm socket
- Extender X2
- Long 10mm socket
- Hammer
- 15mm wrench
- Flathead screwdriver
- Gimbal
- 22mm wrench
- Torque wrench : [ Ссылка ]

Don't forget to subscribe : [ Ссылка ]

🛻 COMPATIBLE VEHICLES
The operation and tools displayed in the video should be available on the following vehicles :
- 2009 Ford F150
- 2010 Ford F150
- 2011 Ford F150
- 2012 Ford F150
- 2013 Ford F150
- 2014 Ford F150

📽 🛠 USEFUL VIDEOS 🛠 📽
- How to jack your Ford F-150 safely : [ Ссылка ]

⚠️ CARPARTS.COM'S INFOS
- Raise the front of your vehicle high enough, which will allow you to remove the catalytic converter later.

- We advise you to have someone help you to hold the catalytic converter assembly in place to prevent it from falling when unscrewing.

- Each oxygen sensor has a different cable length. Take the example of the old line so as not to invert the sensors.

🚨 DISCLAIMER
This video is for entertainment purposes only. Carparts.com, Inc. disclaims all damages including, but not limited to, actual, consequential, and/or punitive, for any liability, claim, or any other injury or cause related to or arising from any information or lack thereof posted in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All mechanical car projects entail some risk. It is the sole responsibility of the viewer to assume this risk. If you are in doubt, please consult a licensed mechanic in your area.

📚 CHAPTERS
0:00 Intro
0:10 How to pull up your F150
0:50 Uncouple the exhaust line from the catalytic converter assembly
1:14 Remove the Crosspiece taht holds the gearbox
2:39 Remove the gearbox mount and the driveshaft
4:41 Disconnect the O2 sensors
5:05 Uncouple the catalytic converter to the exhaust manifold
6:02 Tips before removing the catalytic converter
6:33 Put the O2 sensors back
7:22 Install the passenger side cat converter
8:06 Install the driver side cat converter
8:42 Put the gearbox mount back in place
8:57 Reconnect the O2 sensors
9:40 Recrew the gearbox mount + Tightening torques
10:11 Reconnect the cat converter to the exhaust line
10:45 Put the driveshaft back in place
11:13 Put the Crosspiece back in place
11:51 Put your F150 on the ground

свернуть