SSV solenoid only $10 [ Ссылка ]
Mazda RX-8 Related Service videos
1. How To Install RX-8 Spark Plugs Correctly with 2 Trailing Spark Plugs on top and 2 Leading on bottom [ Ссылка ]
2. How to install Ignition Coils in correct order with Leading 1 Trailing 1 Leading 2 Trailing 2
[ Ссылка ]
3. Mazda RX-8 P0661 Check Engine code problem solved [ Ссылка ]
4. How to Pre Mix 2 Cycle Engine Oil into Mazda RX-8 [ Ссылка ]
5. Mazda RX-8 P0661 Code How to test Solenoids correctly to find the bad ones [ Ссылка ]
Mazda RX8 won’t start or will start a die Red battery icon on dash problem solved
How to Start a Flooded Mazda RX8
Depress and hold the accelerator pedal and crank the engine for eight seconds. This will clear out any fuel that has flooded the combustion chamber.
Release the accelerator pedal and start the engine. It is not necessary to press the pedal again. The engine should start without adding more fuel.
What is the remedy when engine won't start but cranks normally?
Answer: The most common source of trouble when the engine cranks but won't start is the ignition or fuel system. Make sure you got enough fuel pressure and good spark. Also, a faulty sensor (crankshaft position sensor or camshaft sensor on some models or throttle position sensor) may cause this problem as well.
What causes Mazda RX8 hot start problem?
There are 2 main reasons why your car may develop 'hot-starting' issues: Your engine may be suffering from low compression. Your engine may have a slow starter motor.
How do you reset an RX8?
In the RX8 there was a way to reset the ECU manually, not sure what the technical stuff behind it but you: 1. Hold the odo reset button in while you turn the battery on (not the car) and hold for about 10 seconds, you'll see the word test appear and you can scroll through these weird menu's
Why do rotary engines flood?
Fuel injected rotary powered cars are prone to flooding by nature. ... Electrical problems such as slow cranking speed due to weak alternator, bad battery/ground, or starter can result in too much fuel being injected, saturating the spark plugs.
Why is my car turning on but not starting?
If your vehicle won't start, it's usually caused by a dying or dead battery, loose or corroded connection cables, a bad alternator or an issue with the starter. It can be hard to determine if you're dealing with a battery or an alternator problem.
What would cause my car not to start?
If your car won't start even after you check the steering wheel and make sure you have gas, it could be due to one of the following: Dead battery. A dead battery is the most common reason why a car won't start. If you have a battery tester, check your battery to see if it's weak.
How do you diagnose a car that won't start?
Diagnose: Why Won't My Car Start
1) Is the engine cranking? ...
2) Check the trouble code memory. ...
3) Check the crankshaft/camshaft sensors. ...
4) Check the fuel pressure. ...
5) Check the spark from the ignition coil. ...
6) Check if the injectors are opening. ...
7) Check the crankshaft/camshaft timing. ...
8) Check compression/leak down test.
How much does it cost to rebuild an rx8 engine?
A proper rebuild, one that goes beyond running (120+ PSI warm compression numbers) will be north of $4000. With upgrades for power and longevity, you can expect to pay $6k. A Mazda remanufactured engine comes with new housings, irons, rotors, seals, etc for as low as $2900
How fast does a rx8 go?
145 mph
Engine: 1.3-liter, rotary engine
Torque: 159 pound-feet
Transmission: Six-speed Manual
0-60 mph: 6.4 seconds
Top Speed: 145 mph
What's bad about rotary engines?
Rotary engines have a low thermal efficiency as a result of a long combustion chamber and unburnt fuel making it to the exhaust. ... Finally, emissions are poor and fuel economy is terrible, and ultimately this is the cause of it's death.
What causes low compression in a rotary engine?
Apex Seal wear, is the primary cause of low engine compression. ... In some cases the seals just wear out naturally, the level of vertical wear exceeds the point in which the apex seal springs can no longer take up the slack causing further gas leakage and thus less compression.
How many spark plugs does a rotary engine have?
two spark plugs
As the chamber passes over the spark plugs, they fire to ignite the mixture. All modern Wankel engines have two spark plugs to ensure that the fuel/air mixture burns evenly throughout the chamber.
What are the signs of a bad ignition switch?
These are the most common symptoms of ignition switch trouble.
Car Fails to Start. One of the most obvious signs of a failing or faulty ignition switch is if the car won't start when the key is turned. ...
Key will not Turn. ...
Vehicle Stalls. ...
No Noise from the Starter Motor. ...
Dashboard
![](https://i.ytimg.com/vi/dAwoQDSCqq4/maxresdefault.jpg)