Thanks for watching ! As promised, below I've attached all the necessary links to either build your own race whoop or get one ready to fly from the Five33 shop!

Want so support the channel? Consider shopping at Five33!

Ready To Fly Whoop: ?utm_source=copyToPasteBoard&utm_medium=product-links&utm_content=web
Parts Picker Page: [ Ссылка ]

Parts:
Frame: [ Ссылка ]
AIO: [ Ссылка ]
Camera: [ Ссылка ]
Motors: [ Ссылка ]
Props: [ Ссылка ]
Batteries: we bleed (ph 2.0) [ Ссылка ]
- [ Ссылка ]
VTX: [ Ссылка ]

Tools
T700 Glue: [ Ссылка ]

B600 Glue: [ Ссылка ]

Phillips Driver: [ Ссылка ]



Mr.Chaus Drone Tune

Esc settings

48khz PWM frequency
Demag High



# version
# Betaflight / STM32F411 (S411) 4.4.3 Nov 14 2023 / 17:22:54 (738127e7e) MSP API: 1.45

# config: YES

# start the command batch
batch start

# reset configuration to default settings
defaults nosave

board_name BETAFPVF411
manufacturer_id BEFH
mcu_id 003900393535510936323431
signature

# name: mrchaus

# feature
feature -TELEMETRY

# serial
serial 1 2048 115200 57600 0 115200

# beacon
beacon RX_LOST
beacon RX_SET


# master
set gyro_lpf1_static_hz = 500
set gyro_lpf2_static_hz = 1000
set dyn_notch_count = 2
set dyn_notch_q = 500
set gyro_lpf1_dyn_min_hz = 500
set gyro_lpf1_dyn_max_hz = 1000
set acc_calibration = -64,194,21,1
set min_check = 1010
set max_check = 1990
set rc_smoothing_auto_factor = 25
set rc_smoothing_auto_factor_throttle = 25
set blackbox_sample_rate = 1/2
set dshot_idle_value = 600
set dshot_bidir = ON
set dshot_bitbang = ON
set motor_pwm_protocol = DSHOT300
set motor_poles = 12
set vbat_max_cell_voltage = 438
set yaw_motors_reversed = ON
set small_angle = 180
set pid_process_denom = 1
set simplified_gyro_filter_multiplier = 200
set osd_vbat_pos = 385
set osd_rssi_pos = 226
set osd_link_quality_pos = 2454
set osd_rssi_dbm_pos = 321
set osd_tim_1_pos = 2433
set osd_tim_2_pos = 406
set osd_flymode_pos = 374
set osd_throttle_pos = 2401
set osd_crosshairs_pos = 203
set osd_craft_name_pos = 2441
set osd_warnings_pos = 14353
set osd_avg_cell_voltage_pos = 2049
set osd_canvas_width = 30
set osd_canvas_height = 13
set vtx_band = 5
set vtx_channel = 8
set vtx_power = 2
set vtx_low_power_disarm = ON
set vtx_freq = 5917
set gyro_1_sensor_align = CW90
set gyro_1_align_yaw = 900
set rpm_filter_harmonics = 2
set craft_name = mrchaus

profile 0

# profile 0
set dterm_lpf1_dyn_min_hz = 97
set dterm_lpf1_dyn_max_hz = 195
set dterm_lpf1_static_hz = 97
set dterm_lpf2_static_hz = 195
set vbat_sag_compensation = 100
set p_pitch = 69
set i_pitch = 74
set d_pitch = 64
set f_pitch = 175
set p_roll = 66
set i_roll = 70
set d_roll = 56
set f_roll = 168
set p_yaw = 66
set i_yaw = 70
set f_yaw = 168
set d_min_roll = 52
set d_min_pitch = 59
set feedforward_averaging = 2_POINT
set feedforward_smooth_factor = 65
set feedforward_jitter_factor = 3
set feedforward_boost = 18
set simplified_master_multiplier = 140
set simplified_i_gain = 60
set simplified_d_gain = 125
set simplified_pi_gain = 105
set simplified_dmax_gain = 25
set simplified_dterm_filter_multiplier = 130

profile 1

profile 2

profile 3

# restore original profile selection
profile 0

rateprofile 0

# rateprofile 0
set rates_type = BETAFLIGHT
set roll_rc_rate = 90
set pitch_rc_rate = 80
set yaw_rc_rate = 70
set roll_srate = 70
set pitch_srate = 70
set yaw_srate = 70
set throttle_limit_type = SCALE

rateprofile 1

rateprofile 2

rateprofile 3

# restore original rateprofile selection
rateprofile 0

# save configuration

свернуть