Try out PCBWay: [ Ссылка ]
Get $5.00 in-credit welcome bonus after joining: [ Ссылка ]
---------------------------------------------------------------------
In this video, we're making a fast indoor/outdoor mini racing drone from some common materials, also using a JJRC/Eachine drone receiver board with a mini transmitter.
With a calculated top speed of around 30-35kph or 18-21mph, this racing drone is a true racer! It can handle being flown outdoors even in windy-ish conditions!
----------------------------------------------------------------------
👉 Visit my online Storefront: [ Ссылка ]
----------------------------------------------------------------------
☕ Buy me a coffee: [ Ссылка ]
----------------------------------------------------------------------
Instagram: @max.imagination - [ Ссылка ]
Instructables page: [ Ссылка ]
----------------------------------------------------------------------
Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!


Parts and materials needed to build this mini drone:
(x1) Transmitter/controller + Receiver - [ Ссылка ]
(x4) 3.7V 6mm High-speed Coreless motor - [ Ссылка ]
(x4) Propellers - [ Ссылка ]
(x1) 3.7V 150mAh Li-Po battery - [ Ссылка ]
Or 3.7V 220mAh Li-Po battery - [ Ссылка ]
(x1) Short section of Plastic Cable Raceway (Trim off and use "U"-shaped sections) - [ Ссылка ]
(x3) Popsicle sticks - [ Ссылка ]
(x1) Old ink pen
(x1) Square piece of foam

🪛🔧🔨 Tools and extra supplies I use:
➡️ Soldering Iron Kit - [ Ссылка ]
➡️ Hot Glue Gun - [ Ссылка ]
➡️ Drill Machine - [ Ссылка ]
➡️ Box cutter/Utility knife - [ Ссылка ]
➡️ X-Acto Hobby Knife - [ Ссылка ]
➡️ Cutting Matt (Green) - [ Ссылка ]
➡️ Needle-nose Pliers - [ Ссылка ]
➡️ Wire Cutters for Electronics - [ Ссылка ]
➡️ Wire-stripping tool (Automatic) - [ Ссылка ]
➡️ Screwdriver kit - [ Ссылка ]
➡️ Heat-shrink Tube Kit - [ Ссылка ]
➡️ Jumper Wire Kit - [ Ссылка ]
➡️ Breadboard for Prototyping - [ Ссылка ]
➡️ Perf Boards, Pin headers, and Connectors Kit - [ Ссылка ]
➡️ Superglue - [ Ссылка ]
➡️ Duct Tape - [ Ссылка ]
➡️ Double-sided Tape - [ Ссылка ]
➡️ Kapton Tape (for battery leads) - [ Ссылка ]
---------------------------------------------------------------

//////////////////////////
Music credits:
Roboskater by Audionautix is licensed under a Creative Commons Attribution 4.0 license. [ Ссылка ]
Artist: [ Ссылка ]
Hip Hop Rap Instrumental (Crying Over You) by christophermorrow
[ Ссылка ]
Creative Commons — Attribution 3.0 Unported— CC BY 3.0
Free Download / Stream: [ Ссылка ]
Music promoted by Audio Library [ Ссылка ]
V.I.P.N - "SKY" MOONY TRAP BEAT | No Copyright Trap
Free Download Link
[ Ссылка ]
V.I.P.N
[ Ссылка ]...
[ Ссылка ]
[ Ссылка ]
[ Ссылка ]
//////////////////////////

You may have also found this video by searching the following keywords:
drone, quadcopter, racing drone, diy drone, diy quadcopter, homemade,
homemade drone, diy, how to make, how to, fast drone, easy to make, simple drone, easy to make drone, drone that can fly, flying drone, flying, budget drone build, drone build, rc, remote control, radio control, rc drone, at home, mini rc drone, mini drone, helicopter, copter, rc aircraft, aircraft, hover, Mini RC racing drone, DIY quadcopter, Fast mini drone, RC drone building, Mini racing drone tutorial, DIY racing quadcopter, How to make a mini drone, Build your own racing drone, Mini quadcopter DIY guide, Fast RC drone build, Mini drone racing tutorial, Step-by-step drone assembly, Racing drone building tips, DIY mini racing quadcopter, RC drone, Mini drone speed modifications, Racing drone components, Building a fast quadcopter, Mini drone racing techniques, Customizing your racing drone, Tips for building a mini racing drone, Mini drone modification guide, Building a lightweight racing quadcopter, Racing drone electronics guide, Mini drone aerodynamics tips


#racingdrone #quadcopter #diydrone

свернуть