Buy Industrial Automation Training Book From Here -
1. [ Ссылка ]
2. - [ Ссылка ]
3. - [ Ссылка ]
4.- [ Ссылка ]
.
.
.
.
Why IGBT is very popular nowadays?
Lower hate requirements
Lower switching losses
Smaller snubber circuit requirements
What are the different methods to turn on the thyristor?
Forward voltage triggering
Gate triggering
dv/dt triggering
Temperature triggering
Light triggering
What is the difference between power diode and signal diode?
difference-between-power-diode-and-signal-diode
IGBT is a voltage controlled device. Why?
Because the controlling parameter is gate-emitter voltage
Power MOSFET is a voltage controlled device. Why?
Because the output (drain) current can be controlled by gate source voltage
Power BJT is a current controlled device. Why?
Because the output (collector) current can be controlled by base current.
What is the relation between α and β?
relation between α and β
What are the different types of power MOSFET?
N-channel MOSFET
P-channel MOSFET
How can a thyristor turned off?
A thyristor can be turned off by making the current flowing through it to zero.
Define latching current.
The latching current is defined as the minimum value of anode current which it must attain during turn on process to maintain conduction when gate signal is removed.
Define holding current.
The holding current is defined as the minimum value of anode current below which it must fall to for turning off the thyristor.
What is a snubber circuit?
It consists of a series combination of a resistor and a capacitor in parallel with the thyristors. It is mainly used for dv / dt protection.
Take Power Electronic Tests : Top 1000 Power Electronics Online Tests
What losses occur in a thyristor during working conditions?
Forward conduction losses
Loss due to leakage current during forward and reverse blocking.
Switching losses at turn-on and turn-off.
Gate triggering loss.
Define hard-driving or over-driving.
When gate current is several times higher than the minimum gate current required, a thyristor is said to be hard-fired or over-driven. Hard-firing of a thyristor reduces its turn-on time and enhances its di/dt capability.
Define circuit turn off time.
It is defined as the time during which a reverse voltage is applied across the thyristor during its commutation process.
Why circuit turn off time should be greater than the thyristor turn-off time?
Circuit turn off time should be greater than the thyristor turn-off time for reliable turn-off, otherwise the device may turn-on at an undesired instant, a process called commutation failure.
What is the turn-off time for converter grade SCRs and inverter grade SCRs?
Turn-off time for converter grade SCRs is 50 – 100 ms turn-off time for converter grade SCRs and inverter grade SCRs and for inverter grade SCRs is 3 – 50 ms.
What are the advantages of GTO over SCR?
Elimination of commutation of commutating components in forced commutation, resulting in reduction in cost, weight and volume.
Reduction in acoustic noise and electromagnetic noise due to elimination of commutation chokes.
Faster turn-off, permitting high switching frequencies.
Improved efficiency of the converters.
What is meant by phase controlled rectifier?
It converts fixed ac voltage into variable dc voltage.
Mention some of the applications of controlled rectifier.
Steel rolling mills, printing press, textile mills and paper mills employing dc motor drives.
DC traction
Electro chemical and electro-metallurgical process
Portable hand tool drives
Magnet power supplies
HVDC transmission system
What is the function of freewheeling diodes in controlled rectifier? It serves two process.
It prevents the output voltage from becoming negative.
The load current is transferred from the main thyristors to the freewheeling diode, thereby allowing all of its thyristors to regain their blocking states.
What are the advantages of freewheeling diodes in a controlled in a controlled rectifier?
Input power factor is improved.
Load current waveform is improved and thus the load performance is better.
What is meant by delay angle?
The delay angle is defined as the angle between the zero crossing of the input voltage and the instant the thyristor is fired.
What are the advantages of single phase bridge converter over single phase mid-point converter?
SCRs are subjected to a peak-inverse voltage of 2Vm in a fully controlled bridge rectifier. Hence for same voltage and currnt ratings of SCrs, power handled by mid-point configuration is about
In mid-point converter, each secondary winding should be able to supply the load power. As such, the transformer rating in mid-point converter is double the load rating.
Top 50 Power Electronics Interview Question And Answers
Теги
power electronics interview questionspower electronics interview questions and answerspower electronics interview questions for experiencedpower electronics interview questions in hindipower electronics basic interview questionspower electronics questions for interviewpower electronics question seriespower electronics questions gatepower electronics question bankpower electronics questions and answerspower electronics questions series