A super extended trigger, modular design, tool-free maintenance, rotating necks, and flip-flop cable assembly make DELTA-MIG the most versatile, customizable, and easy to use heavy duty air-cooled welding gun in the industry.
Check out the Delta MIG on our Website:
[ Ссылка ]
Don't forget to follow us on social media for more news and knowledge!
Facebook : [ Ссылка ]?...
LinkedIn : [ Ссылка ]...
Instagram : @abicor_binzel
**********
Delta MIG ranges from 300 to 450 amp at 60% duty cycle. If you rate yourself down to 35% and certain gases, you can stretch Delta up to 480 amp really without much problem. Delta MIG has a one of a kind handle design that allows the welder to get as comfortable as possible on the job. They can hold it up high, hold it down low, and then the super long trigger allows them to apply pressure anywhere on Delta to strike an arc and activate the torch. What really makes Delta unique from other welding guns in the market is just how easy it is to do replacement and maintenance of the gun. You can literally replace anything on the Delta MIG with a simple hex wrench. I'm going to demonstrate all that for you over the course of this product overview. Let's start by switching your swan neck out. Really easy to do. There's a little nut that sits right here inside the handle. Just get the hex wrench in there. Quick quarter turn and loosen it up and then you can rotate that neck 360 degrees, no problem. If you you want to swap the neck out, just simply pull it out. Best to use neck liners if you're going to be doing a swap like this, but if it's the same tool center point, same length, you can obviously just keep your wire liner in there and then you can simply just switch your neck, get it to the position that you want and tighten up and you're ready to go. And like with every Abicor Binzel MIG gun, we use high-grade consumables that last longer than other guns on the market including nickel plated nozzles which are great at resisting spatter and also the high grade precision made contact tips which will last longer because there made with the patented technology that allows them to resist micro-arcing and burn-back and all the things that typically plague other contact in makers on the market. You also get lots of great options, like narrow gap consumables like what I'm holding here. Helps you get into those really tight access joints, things like pipe or tight corners, to help you get in there and get that access and get those quality welds out of it. One of the great features of Delta MIG is that it has all sorts of neck bands and handle options to suit the job at hand. We have neck bend for 22 degree, 35 degree, 45 degree. We also have 180 flex necks that can really help you get into those tight access joint areas and handle options including buried, raised, lockout and locking, so you have the right tool for the job. To remove the handle from the Delta MIG gun, take your hex wrench, loosen that tightened nut on the handle. Remove the swan neck, take your locking nut at the base of the handle, undo that, unfold the gull wing handles, remove the wiring and remove the handle. Then put your new handle in. Do all those steps in reverse and then you're ready to weld. Swapping out something like your rear connect with Delta MIG is an easier step even in swapping out your handles. So let's say we have a Euro connect here and we need to switch to something like a Lincoln. Take the hex wrench. There's a tightening nut here similar to at the handle where you would tighten the swan neck. Put your hex wrench in, loosen it up, take out the Euro connect, find your new connect, slide it in, take that hex wrench, tighten it up, and then you're ready to go. A truly innovative feature of Delta MIG is the modularly built cable assembly, and what that means is that the front end of the cable is built exactly the same to the back end. So if your cable is experiencing wear on one side of the torch, you can simply remove the handle and the rear housing from the cable, flip flop them around, put them back in place, and extend the life of your cable and your welding gun even more. Delta MIG comes with a standard cable assembly made for high amperage heavy duty air cooled applications. It also features a lightweight cable option for those looking for a little more comfort on the job. Because of the unique handle design and robust swan neck, Delta MIG's also a great choice for your ABI-CAR welding tractor or hard automation system. If you'd like more information on Delta MIG or want to bring it into your shop and get a demo, contact your local Abicor Binzel sales rep or visit us at binzel-abicor.com. This is Matt from Abicor Binzel. Thanks for watching guys. Have a great day.
![](https://s2.save4k.ru/pic/vh4lpvylM3Y/maxresdefault.jpg)