Have you ever wondered how roofs tie together? Trusses don't fill from one section to the next... So how is it done? Here's how!

0:00 - 2:45 Sleepers installed.
Sleepers are where your rafters will land, these are installed nailed down into trusses or rafters below to ensure a solid connection.

2:46 - 4:09 Ridge Board installed.
The Ridge is where your rafters will but into up at the top, your ridge board creates the 'peak' of the roof. 2x8" ridge board was spec'd here, but many have been done with 2x6".

4:10 - 5:20 Laying out for fill rafters, 24" O.C. from the existing trusses.
You want to continue the roof layout from an existing location to ensure the roof sheathing goes down without conflict. Hooking trusses or rafters that are already in location on a 24" layout, makes sure you don't end up with problems when sheathing.

5:21 - 6:15 Pulling numbers for rafter numbers.
All of my numbers were pulled from long-point of the 63* on a 45* to long-point of the 6/12 head cut at the top of the ridge. Make sure to always pull the same way for every rafter or you'll confuse yourself.

6:16 - 7:59 Cutting rafters.
With numbers pulled up top, everything can be done down below. Cutting all rafters on the ground makes sure we aren't slipping on sawdust up above.

8:00 - 15:40 Installing rafters.
Nailing the rafters on the layouts done earlier on, and down at the sleeper. Make sure to hold your rafter fill flush to top of ridge.

15:41 - 18:50 Bracing / Support for over-framed roof.
This varies structural engineer to structural engineer. For this project he wanted uprights under the longer rafters, seen done here.

18:51 - 20:09 Explaining the roof system.
This should be self-explanatory.

20:10 - 21:27 Roof sheathing installation.
4'x8'x5/8" ZIP System Sheathing from Huberwood: www.huberwood.com/ for more information.

21:28 - 22:34 Project Recap.

_________________

𝑻𝑶𝑶𝑳 𝑳𝑰𝑺𝑻: [ Ссылка ]

𝑪𝑶𝑵𝑵𝑬𝑪𝑻 𝑾𝑰𝑻𝑯 𝑴𝑬:
_________________
𝑰𝑵𝑺𝑻𝑨: [ Ссылка ]

2𝑵𝑫 𝑪𝑯𝑨𝑵𝑵𝑬𝑳: [ Ссылка ]

𝑭𝑨𝑪𝑬𝑩𝑶𝑶𝑲: [ Ссылка ]

𝑯𝑨𝑴𝑴𝑹: [ Ссылка ]


𝑺𝑷𝑶𝑵𝑺𝑶𝑹𝑺:
__________
𝑨𝑹𝑰𝑨𝑻 10%: [ Ссылка ]

𝑫𝑰𝑨𝑴𝑶𝑵𝑫𝑩𝑨𝑪𝑲 𝑻𝑶𝑶𝑳𝑩𝑬𝑳𝑻𝑺: [ Ссылка ]

𝑩𝑨𝑫 𝑾𝑶𝑹𝑲𝑾𝑬𝑨𝑹: [ Ссылка ]
(CODE: "𝕄𝔹𝕎𝟙𝟘")

#construction #building #carpentry

свернуть