More, here in the video description:

I started with a V0.0 Kit from Aliexpress (now it's 0.1, which is better in any respect)*:
Formbot Voron V0.1 Kit (AliExpress) [ Ссылка ]
LDO Voron V0.1 KIT (Caribou3D) [ Ссылка ]

Recommended Kits for bigger DIY printers:
Voron 2.4 Kit (AliExpress) kit bit.ly/3PklmWE
Voron Trident Kit (AliExpress) [ Ссылка ]

STL files, instructions and BOM:
[ Ссылка ]

The full print recorded on a FLIR ONE PRO thermal camera is uploaded!
Awesome motion pictures to realize that the part cooling is just on the limit here.

Settings and 247upgrades done on this printer: Please see below!

I started my build with a kit from Formbot (Aliexpress)
A convenient and good quality start, but you may change/add some parts*:
[ Ссылка ]

After tuning the Voron 0.0 to "247 Stage 1", it is possible to do this feasibility study of a full and uncut 1000mm/s print, which opens potentials for faster daily FDM printing at high quality.
The Voron Zero is a very good basis for tuning at low cost, as the moved parts are light weight.
A great open source design by vorondesign.com!

Detailed explanations will follow:
My series "Deep Dive into Speedprinting" is in the work - stay tuned for that!

Support my work at Patreon:
[ Ссылка ]

My Instagram and Twitter - more about my doings and behind the scenes:
Instagram: [ Ссылка ]
Twitter: [ Ссылка ]

Next Videos:
- complex print at 1000mm/s (RPI holder) - Preview on Instagram/Twitter/Reddit/Facebook!
- entry to "VzSpeedCube challenge" (speed AND quality matter!)
- a speedprint at flawless quality of a 3D Benchy in PLA: way below 10 minutes
- a print of a 3D Benchy as fast as possible: faster than 4 minutes
- Video Series: "Deep Dive into Speedprinting": Motion, Extrusion, Cooling, Software
- More? My list for content is insanely HUGE - keeps me busy for years...

💚Pizza, Beer and Coffee helps me going on💚
[ Ссылка ]
💚Thanks to all who support/ed my work💚


---------------Settings and Setup:

Filament*: ESUN ABS+ - a great choice filament for strong parts and easy printing:
[ Ссылка ]

Layer 1: 200mm/s (requested).
Layer 2: 450mm/s (requested).
Layer 3 to end: 1000mm/s (requested).

T_Hotend = 310C
T_Bed = 80C
Commanded Acceleration/Deceleration: 35.000 mm/s² (rate of velocity change)
square_corner_velocity: 25mm/s (NOT the resulting velocity value at corners)
Nozzle: 0.4mm
Layer Height: 0.1mm
Line width: 0.4mm
Volumetric flow: 40mm³/s
Lengths of straights (between corners): 65mm
Min. lengths of printing @ REAL 1000mm/s: 35mm per straight

Xxxx ALL DESIGNS AVAILABLE SOON xxxX
@ Voron Users / Thingiverse / GitHub


*******UPGRADES 247printing Vzero STAGE 1:


—MOTION* (Part 1: Video Deep Dive)

Nema14 spec Voron V0.1 @1.7A (OMC 14HS20-1504S) [ Ссылка ]

F623 bearings instead of toothed idlers [ Ссылка ]

WD40 specialist dry lubricant for rails [ Ссылка ]

Gates-LL-2GT 6mm belts [ Ссылка ]


— EXTRUSION*: (Part 2: Video Deep Dive)
Slice Engineering Mosquito Magnum (5% off!): [ Ссылка ]

VolcoMosq Block (+9mm melt) designed by Nitram: [ Ссылка ]

E3D Hemera (Bowden config) [ Ссылка ]

Capricorn Bowden Tube [ Ссылка ]

50W heater (24V) [ Ссылка ]

PT1000 temp sensor [ Ссылка ]

Boron Nitride Paste @ heater, thermistor and heat break [ Ссылка ]


— COOLING* (Part 3: Video Deep Dive)
4010 blower fans (24V) on updated toolhead [ Ссылка ]

optimized air ducts for part cooling with aluminium tape insulation [ Ссылка ]

External Static Cooling: 4x4020 fans (24V) [ Ссылка ]

4x40mm heatsink at AB stepper motors [ Ссылка ]

4010 noctua fans (5V) at heat sinks / stepper motors [ Ссылка ]

25mm axial fan (5V) for stepper drivers [ Ссылка ]


— Software / Firmware / Controllers (Part 4: Video Deep Dive)*:

Klipper Firmware: [ Ссылка ]

Raspberry Pi Zero W (Mainsail): [ Ссылка ]

Raspberry Pi 3B (Input Shaping and Octoprint): [ Ссылка ]

Alternative: Raspberry Pi4: [ Ссылка ]

Simplify 3D, multi processes used: [ Ссылка ]


-------------------------------------------------------
My modest video gear*:

iPhone 11 Pro: [ Ссылка ]
Smartphone video rig: [ Ссылка ]
GoPro Hero 9: [ Ссылка ]
FLIR ONE PRO: [ Ссылка ]
Similar to the soft boxes I use: [ Ссылка ]
Similar to the tripod I use: [ Ссылка ]

*Amazon links are affiliate links at no extra costs for you!

#247printing
#JoinTheSpeed
#volcomosq
#VzSpeedCube
#SpeedBoatRace

свернуть